Go to Home Page  
 
 

 

Specification Bar




Component Sizes

Residential Strength

Ovation - Regency

Industrial Strength
Pickets 5/8" sq. x .050"
thick		 3/4 " sq. x .050"
thick		 1" sq. x .062"
thick
Rails: Top Walls
Side Walls		 1" x .055"
thick
1" x .082"
thick		 1" x .055"
thick
1 1/2 " x .082" thick		 1 5/8 " x .070"
thick
1 5/8 " x .100"
thick
Standard Posts 2" sq. x .060"
thick		 2" sq. x .060"
thick		 2 1/2 " sq. x .075"
thick
Gate Posts 2" sq. x .125"
thick
4" sq. x .125"
thick		 2" sq. x .125"
thick
4" sq. x .125"
thick		 4" sq. x .125"
thick
6" sq. x .125"
thick
Spacing Between Pickets 3 13/16"
(1 5/8 " for # 301, # 302)		 3 31/32" 4"
(1 1/2 " for # 301, # 302)
Post Spacing 72 1/2" on center 72" / 95 5/8"on center 71 1/2" on center
Heights Available* 36", 42", 48", 60", 72" 36", 48", 60", 72" 48", 60", 72", 84", 96"
Standard Colors Black, White, Bronze Black, White, Bronze Black, White, Bronze
Weight Supported 350+ lbs. per section 350+ lbs. per section 1,000+ lbs. per section
*Residential fence is also available in a 54" height as a modified Style #200 and #202. Regency fence is available in a 54" height in Windsor and Windsor Plus styles. Ovation is only 48" high.

No Industrial fences are shown on this site. Industrial products are available in the 100, 200 and 300 Series designs. If you would like more information on our Industrial fences, please contact our Sales Department.
FencCoat - Jerith's Powder Coated Finish
Jerith's technologically-advanced powder coating system allows us to produce a high quality, long-lasting finish which is also environmentally friendly. When applied to a Jerith fence, FencCoat is twice the thickness and hardness of a typical acrylic (or "wet paint") finish. Consequently, it is far more durable, fade-resistant, and scratch-resistant than other coatings.

Since its introduction in North America almost 40 years ago, powder coating has become the fastest growing finishing technology. Powder coating contains no solvents and therefore emits negligible amounts of volatile organic compounds (VOC's) into the atmosphere. Wet paints, however, cause severe pollution, both through the emission of VOC's when they are cured and by the generation of excess paint which is considered a hazardous waste. In addition, Jerith's aluminum is prepared for its FencCoat finish with an environmentally safe pretreatment, unlike most wet paints.

To prove the durability of our powder coating, we have tested it extensively. FencCoat endured 3,000 hours of harsh salt-spray and humidity resistance, as well as 5 years of continuous exposure in Florida. Other aluminum fence manufacturers have performed similar tests on their own coatings, yet they only survived 1,000 hours of salt-spray and humidity testing and 1 year of Florida exposure (as stated in their literature). That is why we are confident enough to guarantee that our FencCoat finish will last for as long as you own your Jerith aluminum fence.

Jerith's Exclusive HS-35™ Aluminum Alloy

You no longer have to choose between the maintenance-free ease of aluminum and the strength of steel for your fence. The best of both worlds is available only from Jerith. Through extensive research and testing, Jerith has developed an aluminum alloy called HS-35. This remarkable material has the strength of steel without the rust!

Our HS-35 Alloy has a minimum yield strength of 35,000 pounds per square inch (psi), which is significantly higher than the 25,000-33,000 psi strength found in most steel fences. Even more impressive is Jerith's advantage over other aluminum fences, which have yield strengths of only 16,000 psi.

Every post and rail in Jerith aluminum fences is extruded from our exclusive HS-35 Alloy. While some aluminum fence manufacturers claim to use similar alloys, they seldom use it in both their posts and rails like we do. In addition, Jerith is the only manufacturer that uses a high strength alloy in its pickets. Our pickets are over 50% stronger than any other aluminum fence. We don't cut corners on the strength of our products!

An independent testing laboratory has proven that a typical Jerith Residential Fence can support over 350 pounds per section without any structural failure and our Industrial fence can hold over 1,000 pounds! With strength like this, Jerith fences will certainly satisfy your fencing needs for years to come.

Always look for our logo on the sections, post caps, and gates to ensure that you are receiving Jerith quality and our exclusive HS-35 Alloy. Other fences may look like Jerith, but none are as strong, durable or well-built as ours.
Go to Page Top
FEATURES STYLES 1 2 3 4 5 6 7 8 9 10 11 12
Rail Top - pickets stop at top rail            
Pinched Points - standard on most styles          
Hoops - installed in field                    
Finials - installed in field                  
Heights available in 3, 4, 5 and 6'      
Heights 3, 4, 5' have 3 rails, 6' has 4 rails      
Height available in 48'' only - 3 rails                    
Height available in 54'' only - 2 rails                      
Sections rack 12'' *          
Sections rack 8'' *                
Sections rack 24'' *                      
Pickets and rails heavier than other styles                      
Picket spacing is 3-13/16''      
Picket spacing is 3-31/32''                      
Picket spacing is 1-5/8''                    
Post prices include flat caps
Post spacing is 72-1/2" on center
Pool Safe - meets Boca Pool Code **                  
Magna-Latch™ included with gates                      
Gates include self-closing hinges and latches
FEATURES STYLES 1 2 3 4 5 6 7 8 9 10 11 12

 

Go to Page Top

PAGE LAST UPDATED
Saturday, June 10, 2006

 

© 1999-2006 - ATLANTIC COAST FENCE COMPANY, INC.
NO PART OF THIS WEB PAGE MAY BE ALTERED, COPIED OR USED IN ANY
FORM OR FORMAT WITHOUT THE EXPRESS WRITTEN CONSENT OF
ATLANTIC COAST FENCE CO., INC. ACF WEBMASTER